Playstation 2 laser replacement

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws.

Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of screws and feet. Remove all the feet and screws in the bottom of the case. The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray.

Playstation 2 laser replacement

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz. Discover the latest stuff from our wide range of partners, including exclusives only available at ZedLabz. Gaming display stands See More "Close Cart". Merchandise See More "Close Cart". Brands See More "Close Cart". Leave a comment Name Email.

Badges: Have you removed the security solder blob? Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place.

.

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Remove all six 4. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit.

Playstation 2 laser replacement

Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of screws and feet. Remove all the feet and screws in the bottom of the case. The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray. Peel the warranty sticker located next to the main power switch straight away from the case.

Mlb stats league leaders

Step 6. Step 4. Thank you for caring enough to show us how to do this and for your time. Fix Your Stuff Community Store. Step 7 Remove laser. Replacing the laser requires you to have or purchase a new laser. I noticed that many times when you replace a lens it throws of the rotary motor. What you need. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Step 1 Outer Shell. Author with 1 other contributor. You are appreciated. Where do you recommend getting the actual part? Disconnect all cables from the console and flip the unit over to reveal its base. All new Lenses have this somewhere in the circuitry.

The screws on the right are a bit deeper inside the shell as like the rest but are the same size. Separate the clips at the front and the overhanging side from their mounting using a Prying Tool.

Step 1 Top Cover. Author with 1 other contributor. View Statistics:. Mohsen - Jan 21, Reply. Introduction Hi! I am also looking for the best quality part. View Statistics:. Excellent guide! Badges: Some ps2 consoles have only 1 hex adjustment yet others have 2.

1 thoughts on “Playstation 2 laser replacement

Leave a Reply

Your email address will not be published. Required fields are marked *