Ipod nano button stuck

I will document what I did to fix it here. This article may also be useful for those looking to dismantle or fix their iPod Nano 6th Gen since most of the steps contained here will allow ipod nano button stuck to access all components of the device, ipod nano button stuck. By performing this fix, there is also the chance that you may damage your iPod, so beware of this before you attempt to DIY. I cannot be responsible if you make a mistake!

A system is only as strong as its weakest link and [Roberto Barrios] found that on the sixth generation iPod nano the buttons are the problem. Each consist of a couple of parts; the tactile piece that you see and press, the electrical switch which converts that force into an electrical signal, and a shim that bridges the gap between the two. After two months of use the iPod [Roberto] was fixing had stopped responding to presses of the Power button. It turns out that the shims are attached with double-sided tape. Inspection of the internals revealed that the shim had slid to one side and no longer made contact with the electrical system. With the shim back in place all is well but he made sure to execute this fix on all of the buttons before reassembly. Just goes to show, you get screwed with what pay for.

Ipod nano button stuck

To start the conversation again, simply ask a new question. Page content loaded. May 15, AM in response to Kshaun. May 15, PM in response to Kshaun. Obviously if your buttons are truly broken the above won't work, but worth checking anyway. Next, try restoring the iPod and see if that clears it up. If not, then you may have an actual hardware failure. Sign in. Sign in Sign in corporate. User profile for user: Kshaun Kshaun Author. User level: Level 1. I charge my Ipod, and then take it out the right way. This is getting on my nerves. Do anybody know how to fix this problem? I might have to get another one or send in for repairing.

It most likely will be too thick. User profile for user: PT PT. I had my warranty on it, so I took it to the store I bought it at and they replaced my iPod.

When I opened the iPod and reached the back side of the power button, it found the shim that actually presses the switch was held in place with double-side sticky tape. With use and probably with the help of high temperatures, the shim slides to the border of the button, away from the switch underneath. This is why the button no longer actuates the switch and does not give the tactile feedback, feeling loose or stuck. After removing the shim and the double tape, I cleaned the back button surface and the shim with acetone. The goo traces are very sticky but it is very important to remove every bit and leave the surfaces clean and dry.

If your iPod isn't responding, a simple force restart should unfreeze it. You only need to know which buttons to press and in what order to force the device to reboot and reload its software. A force restart is a hardware-level reset that physically cuts off power flow from the battery to the logic board. This causes your music player to turn off and restart without deleting your settings, music, or data. Apple no longer sells the iPod, but that's hardly stopping enthusiasts from dusting off their rusty old music players. Yes, you can still use the original iPod today , although you might encounter random freezes, sudden restarts, and unresponsiveness. If your iPod is acting up, the first troubleshooting step is confirming that the Hold switch is in the OFF unlocked position. When slid to the ON locked position, the iPod's buttons are inactive to avoid unwanted presses in your pocket.

Ipod nano button stuck

Repair information for the 6th generation iPod nano. Released in September of Model Number: A Emily Routh emilyrouth.

Audible com uk

There is a small gasket around the power button—that one I removed completely because it caused me a lot of trouble. This article may also be useful for those looking to dismantle or fix their iPod Nano 6th Gen since most of the steps contained here will allow you to access all components of the device. My Nano-6th gen. Posted: Apr 9, Options Permalink History. So, nobody know how to fix it. Once all edges of the screen are free, turn the screen over like you are reading a book. Possibly though I think it would not be as reliable since you probably need it to be made of metal if it is the part that makes electrical contact…. If you are unsure, use standard A4 paper soaked in superglue. If you look into the gap, you will see the glue stretching. Let see what happens…….. My older 6th Gen iPod Nano does the same thing and has been out of warranty for some time. Landing on its edge, all that happened was it dented the metal case and wedged the volume button permanently up. Get started with your Apple ID. Once you have freed the top, bottom and right edges of the screen, pull the screen gently towards the right by holding the top and bottom edges. The cable is too small to repair our selves.

To start the conversation again, simply ask a new question.

You can use superglue, or the more forgiving alternative, contact glue. I'm using this video to fix my iPod. Hi, you may have damaged the ribbon cable which connects all those buttons to the logic board. The reason for this is simply wear on the small dome switch inside. Do not attempt to pull it out too far! Once you have freed the top, bottom and right edges of the screen, pull the screen gently towards the right by holding the top and bottom edges. This is not a good feature, not sure if it is still under warranty. Just got my Ipod nano 6th gen in June, ! All I have is a white screen. Can't see the screen, but it will do until I break down and buy another or Santa brings me one. It requires very small tools, a magnifier, good light and patience. Just replaced it. Do you have any? See if you have any plastic packaging from say, an AA battery pack, as that is thinner than most business cards.