How to reset brake pad sensor on bmw

Remember Me? General BMW Discussion. Just changed front brake pads

Remember Me? Successfully reset brake pad sensor service warning. The installer tied up the brake pad sensors and I had no issues after install of the BBK. A few months ago I got the Service light reminder warning in the cluster. An indy mechanic had good intentions and went into the service menu and reset the service reminder. Unfortunately, this either triggered or left on the brake pad sensor warning.

How to reset brake pad sensor on bmw

Remember Me? Front brake pad service reset. Hello, I have changed the front brake pads to the car without changing the wear sensor and it does not let me reset the service, it does not let me either from the hidden menu of the instrument panel, nor with the INSTA-D. Does anyone know how to reset it without having to change the wear sensor? Appreciate 0. If the wear sensor triggered to indicate the pad change is needed, then either a new sensor or possibly a hack to short the sensor wires together is the only thing that is going to work. The sensors are cheap, so it sounds like the best way to go. First Lieutenant. If the warning was triggered then you'll need new sensors. The warning has not been activated, it only appears that there are km to go for service in yellow. I changed the pads thinking that if the sensor was not activated I would not have to change it and now it does not let me reset the service, as I have read, it is because it lets you reset it if a new sensor is not mounted

If it's the latter maybe because the wire was jiggled, bent or tuggedI'd guess a new sensor is in order. This causes a brake pad warning every time you start the car and more annoyingly the red BRAKE warning light in the cluster remains on and does not turn off when driving. You have to reset the light by leaving the ignition switch on position 2 for about 30 sec.

Remember Me? I recently changed the front and rear brake pads and sensors. I managed to delete the request to replace the front pads but for the back plates I fail. I tried with the handbrake applied and with it not pulled but I still can't reset it " it comes back with reset unsuccessful". I reset it by removing the sensor and putting a clip to make contact between the two wires. But when I insert the sensor the error reappears.

The brake pad warning light, also known as the brake wear indicator light, is a feature found in most modern BMWs designed to alert the driver when their brake pads are wearing thin BMWUSA. When this light is illuminated, it indicates that the brake pads have reached the minimum thickness recommended by the manufacturer and should be replaced as soon as possible. First and foremost, if your brake pad warning light has come on, ensure that you replace your brake pads. This is not a warning that should be taken lightly, as it concerns the safety of your vehicle. Take your car for a test drive to ensure that the new brake pads are functioning properly and that the warning light does not reappear. If the light does come back on, you may need to check the sensors or consult with a professional mechanic for further diagnosis. While resetting the brake pad warning light is typically a straightforward process, sometimes the light can indicate a deeper problem with your braking system. They can accurately diagnose the problem and carry out the necessary repairs Car and Driver. By following the steps outlined above, you can effectively replace your brake pads and reset the warning light.

How to reset brake pad sensor on bmw

Log in. Sign up. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. I replaced my rear brake pads. I did not replace the sensor. Note that there is only one sensor on the rear, on the passenger side Then, when the reset did not work, I went and bought the sensor and replaced it. Then tried the reset again and it did not work. Then someone told me to check my brake fluid, I did that, topped the master cylinder off and then tried the reset again, still doesnt work. The process to reset the warning works in the sense that all of the instructions that I follow from the online posts work as expected.

Gas cylinder morrisons

You will notice your trip meter reset and then go back to the value it once was. I have the same issue as lamia2super, it doesnt show me the mileage and is lit up in yellow. Originally Posted by gismo3. Appreciate 0. Find More Posts by lamia2super. Sorry to revive such an old thread but i tried this, i reset every option available and the red brake light is still on. User Name. Quote: Originally Posted by gismo3 I have had the brakes and sensor replaced, but still get the warning light for the rear brakes. Page 1 of 2 1 2 Last Jump to page:. I recommend buying a new wear pad sensor as well because now light will lit up when you're way below spec less than 3mm.

You hop into your BMW, insert the key into the ignition, and notice — uh oh, that dreaded brake warning light is glaring angrily on your dashboard. Resetting the BMW brake light is actually quite straightforward. If the brake pad warning light illuminates in your BMW, you likely need to reset the brake sensor rather than your brakes needing replacement.

So i took it to BMW, they confirmed that the pads were replaced and they installed a new front sensor because the pads were completely similar. Keep holding for a couple more seconds At this point, service values that can be reset will come up. I tried with the handbrake applied and with it not pulled but I still can't reset it " it comes back with reset unsuccessful". If it is still counting down i. What brand sensor you using? You will probably need to dismantle the brakes the access the pad to add the cable. Remember Me? Find More Posts by lawrencedchan. Similar threads A. Log in. Thread Tools Show Printable Version.