How to change a headlight bulb in a ford focus

Log in. Sign up.

Changing the dipped beam bulb on the old Mk1 Ford Focus can seem daunting, and I have read different ways of doing it. This is the way I was shown by a Ford engineer, and when you have done it once it is very quick and easy. It involves removing the headlight assembly. The main obstacle is the retaining bolt under the car! My local car hardware chain store seemed insistent that the Mk1-facelife Mk 1. The Mk1. Remove the two bolts on the headlight unit as shown in the figure using the 10 mm socket wrench.

How to change a headlight bulb in a ford focus

Ford's Focus uses a Halogen H7 bulb in its low-beam socket. Open the bonnet and remove the two Torx screws holding the headlight in place, then lift the headlight forward and out of the car. Unplug the wiring connector on the back, then remove the rubber boot weather seal on the back of the headlight. Undo the grey clip holding the headlight bulb in place, then remove the old bulb. Refitting the headlight is the opposite process. Adjusting the headlight aim should be done by professionals to ensure the light doesn't blind oncoming traffic, while also properly illuminating the road in front of the car. How do you change headlight bulb and adjust Ford Focus headlights? Answered by CarsGuide. Disclaimer: You acknowledge and agree that all answers are provided as a general guide only and should not be relied upon as bespoke advice. Carsguide is not liable for the accuracy of any information provided in the answers. Other Ford Focus Problems. Can I put the motor of a Ford Focus in a model? Are there any known transmission issues with a Ford Focus manual?

Step 3 Locate the bulb cover found just behind the headlight assembly and remove it by turning it counterclockwise. These bolts and the one under the car you will soon remove are identical.

The Ford Focus first sprung on the automotive scene in as a personality-laden replacement for the Ford Tempo. One of this car's calling cards is its headlight design. When one of these unique headlights burns out on your Ford Focus, changing it yourself is a simple repair that will save you time and money. Ensure that the headlights on your Ford Focus are off by checking you have turned the headlight control all the way to the off position. Make sure your car is off and the keys are out of the ignition, so the daytime lamps are also off.

The only tool needed to change any of the headlight bulbs in either the driver or passenger side housing is a Torx T star bit screwdriver. Locate the two screws that hold the headlight assembly in place. One screw is near the outer edge and the other is at the inner corner. Remove the two screws by turning them counter clockwise with a Torx T star bit screwdriver. Set the two screws aside in a safe place. Turn over the housing and rest it on the bumper. To avoid scratching the plastic lens or the painted bumper, place a towel in between them. Pull off the rubber dust cap on the rear of the housing to access the base of the old low beam bulb. Pry up the black plastic tab on the electrical connector before sliding it straight off the bottom of the old bulb.

How to change a headlight bulb in a ford focus

Headlight Size. Select year Headlight Bulb High Beam - These bulbs produce over 12, lumens of pure high-quality light!

Dell curry raptors

They are not the same as the ones from the grill plastic trim however, which also need removing, so don't mix them up Your instructions, tips and images made this task a doddle! Moral: don't let anything bulbs, screws slip out of your hands, don't leave any tools lying on a handy bit of engine. Please Note, in all the following sections, Right-Hand and Left-Hand are referring to the headlights as seen looking forward from the driver's seat NOT as you look at them from the front of the car. Second step - Gentlemen, choose your headlight! I used a bit of clean kitchen paper to pull out the old bulb and then push in the new one. Clip the grill back on and put the bolt and washer back. It passes over the bulb and connector. Nice one. Unplug the wiring connector on the back, then remove the rubber boot weather seal on the back of the headlight.

Changing the dipped beam bulb on the old Mk1 Ford Focus can seem daunting, and I have read different ways of doing it. This is the way I was shown by a Ford engineer, and when you have done it once it is very quick and easy.

Now place the bulb in the headlight. Replace the wire clip and bulb cover, as well. Tools needed - ratcheting socket wrench, 10 mm socket, and an extender piece. It was a really easy job with your help. Lift the hood and secure it in place with the yellow end of the hood's strut in the designated holes. Align the bulb with the slots in the unit — it will only fit one way. This is the way I was shown by a Ford engineer, and when you have done it once it is very quick and easy. Open bonnet and secure. I did dipped beams on both sides in 20 minutes. That'll confuse you! This is the most inconvenient bit. Many thanks Ray.