Fanuc 21i-t parameter manual

Upload aoaby. Embed Size px x x x x Warning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment ormay be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, aWarning notice is fanuc 21i-t parameter manual.

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page.

Fanuc 21i-t parameter manual

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

The machine coordinates on a master axis and slave axis are monitored. When DLZ of parameter No.

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment.

Mr krabs with money

VGR Any gear ratio between spindle and position coder in rigid tapping 0 : Not used The gear ratio is set in parameter No. However, the current position in the CNC includes a servosystem delay, so that the position is shifted from the machineposition by an amount corresponding to the servo systemdelay. The setting inparameter No. This parameter is used to set a positional deviation limit imposed whilethe tapping axis is stopped in rigid tapping using the second spindle. This parameter sets the common variable number of the custom macro towhich the number of times the tool is retracted after the overload signal isreceived during cutting in a peck drilling cycle mode of a small diameter isoutput. PPD Relative position display when a coordinate system is set 0 : Not preset 1 : Preset NOTE When PPD is set to 1 and the absolute position display is preset by one of the following, the relative position display is also preset to the same value as the absolute position display: 1 The manual reference position return 2 Setting of a coordinate system by G92 G50 for T series G code system A DRL Relative position 0 : The actual position displayed takes into account tool length offset M series or tool offset T series. When the spindle motor, spindle, and position coder are connectedas shown left, let the variables be as follows:. Confirmthat the output voltage is 10V. Thefollowing parameters are supported for each spindle:. Set the allowable error count for the error pulses between two spindles inthe serial spindle synchronization control mode or simple synchronouscontrol mode. NOTE For axes with diameter specification, a diameter value must be set. When or a greater value is set with this parameter, the mirror image function is applied to synchronous control. If0 is set for an axis, movement along that axis is stopped whenever anabnormal load is detected for any axis. See parameter No.

.

Only when the LGT parameter bit 4 of No. Forums New posts Search forums. Monday at AM gregormarwick. Set a master axis number with a slave axis. The following table shows the correspondence between the bits, input signals, and commands. The following parameters are not explained in this manual. SIM When the same block includes a command for an index table indexingaxis and a command for another controlled axis:. Set the coordinate value of the reference position on each axis to be usedfor setting a coordinate system automatically when input is performed ininches. Set this parameter to the slave axis. OHS Operation history sampling is: 0 : Performed. QLG When the passingpoint signal output function is used, the remaining distance to be traveled specified in address ,Q is: 0 : The combined distance of all axes 1 : The distance of the longest axis. RHD When a manual handle interrupt is generated, the relative position display is:0 : Not updated.